Garage Shed Plans | Woodworking Tips

Adept woodworker Ted McGrath created the Ted’s Woodworking Package as a valuable resource which would present woodworkers using some very remarkable thoughts and projects.

The package has various qualities that make it the”#1 woodworking Resource” and some of those attributes alongside a few petty pitfalls will be assessed in this review.

woodworking workshop

What Type of Projects Does Ted’s woodworking Package Contain?

Ted McGrath, the mastermind who made this revolutionary bundle, she’s also an educator and a member of AWI as well. Ted’s woodworking Package contains a varied selection of 16,000 easy ideas and projects, including:

  • Arbor Plans
  • Barn Plans
  • Cabinet Plans
  • Dog House Plans
  • Garage Plans
  • Swing Plans
  • Windmill Plans
  • Many more

woodworking ideas

Woodworkers will find it really easy to start woodworking whenever they are after because most of the thoughts and projects Ted’s source are easy to comprehend and easy. Ted McGrath spent two years researching so that he could gather enough material for an extensive bundle, and he ended up creating a truly’complete’ woodworking resource.

Many may still seem unsure if they should be purchasing Ted’s woodworking Package, despite all of the positive traits. The plethora of resources available online make it more difficult to make the right choice. There are in fact many things that set Ted’s woodworking Bundle besides others.

Ted’s woodworking Project �” Pros and Cons

The Pros

Ideas Suitable for Woodworkers of All Levels

Woodworkers of all levels will be able to benefit from Ted’s woodworking Package. Those that are just getting started will find the ideas and jobs in Ted’s package quite simple. No doubt, complicated carpentry is demanded; however, they will discover that it’s really simple to follow Ted’s simple step by step directions. Presently, both beginner and experienced ones are utilizing Ted’s woodworking Package. The great thing about the thoughts and projects mentioned in Ted’s resource is they can be completed in a very short time.

woodworking projects that sell

Useful Bonuses

Ted McGrath also has three very useful bonuses into the woodworkers who purchase his package, specifically:

  • Free CAD plan and drawing viewer
  • The Complete woodworking Carpentry Guide
  • 150 premium woodworking videos

Complete woodworking Carpentry Guide is two hundred page source which will help beginners learn a whole lot about woodworking. They’ll also be able to advance their woodworking and carpentry abilities through the 150 videos.

Excellently Organized

It’s quite surprising that the content’s in Ted’s woodworking Package are so excellently coordinated although it contains around 16,000 easy woodworking thoughts and woodworking projects. Woodworkers will have the ability to find any project of their choice in this bundle quite readily, even though there so many choices.

60-Day Iron Clad Money-back Guarantee

In general, this product is and those who buy it’ll be backed by a 60-day warranty, so if this woodworking bundle fails to satisfy them, they always have the ability to get their cash back.

The Cons

Requires Time to Download

Ted’s woodworking Package can take a slightly long period to down because of its large size. Nonetheless, using a high-speed internet connection it should download in a couple of minutes.

Slightly Overwhelming

Since there are several ideas, projects and plans in Ted’s woodworking Resource, so a few found it somewhat overpowering and overwhelming. Nonetheless, they didn’t mind being overwhelmed considering the fact that this bundle is indeed impressively organized.

The Most Important Thing

woodworking beginner

The most important thing is that Ted’s woodworking package is so thorough and vast it contains pretty much every woodworking project a woodworker might be interested in constructing.

This woodworking package created by Ted McGrath is truly unmatchable and can’t be compared to those other woodworking bundles that can be found across the net. Ted has done his very best to guide them in every conceivable way he could, through easy to comprehend textual instructions, clear images and even videos as well.

Therefore, woodworkers who purchase Ted’s Woodworking Resource won’t be disappointed with the woodworking thoughts and woodworking jobs they will find inside. Therefore, it is certainly worth buying!

Here is my Beginners List of Woodworking Safety Equipment:

Safety glasses, clear safety goggles, dust masks, face shield, hearing protectors, Nitrile disposable gloves|}
We can go on and off with listing more woodworking hand tools and more woodworking power tools , but the concept is to buy the essential hand and power tools which beginners will need. You can always add to your toolbox as you gain experience!

Garage Shed Plans Guidance for Beginner Woodworking Craftsmen:

At this point you have a great new hobby in woodworking, so you’ve bought your woodworking project plan and you’re really excited to start using your woodworking tools, but how? Your woodworking project plan should provide you step by step directions and techniques to complete your project. But if you are not certain about what to do there is help available! There are lots of places that starting woodworkers can learn about the woodworking craft. First, subscribe to one of those several woodworking magazines available. Each month the authors in woodworking magazines do a story about the best way to increase your woodworking craft. When it’s showing you the way to apply a finish to a finished job, or how to create a mortise and tenon joint, something new could be learned each month. Next, is buying instructional DVD such as the ones made by Fine Woodworking Magazine. Instructional Woodworking DVD’s cover topics such as: Assessing your table saw, the way to work with a router, how to turn wood projects, turning wooden bowls, and wood finishing basics. As you can see, there are many educational resources available for the beginning woodworker to learn the woodworking craft.

|

Woodwork Crafts – The Beginners Guide To Woodworking Garage Shed Plans

If you’re just beginning and very enthusiastic about doing a DIY project for home then, woodworking could be fun. If you do not have the right information, education, and ability, you might land up spending more time and money than you originally intended to spend. As a beginner woodworker, you need to have space, time and the appropriate tools. Having mentioned, there are a couple of essential factors you should remember, before beginning with any woodworking project.

1. If you are a beginner, you should first need to be very interested in woodworking. Making something new with your own hands is a special feeling. Don’t start a project if you’re not interested, as this may land you at a terrible place.

2. Think of the main reason for creating this woodworking project. Choose the uses of this thing you are making.

3. Consider your abilities and examine the time that you have, before you begin with a job.

4. Start jobs that you’re able to complete. If you’re in the middle of a work, then it is wise not to begin any project at all.

Woodwork Crafts – The Beginners Guide To Woodworking Garage Shed Plans

If you maintain those essential points in mind before beginning a woodworking project, it will become very easy for you to reach success. Woodwork requires planning as much because it takes effort. So how do you get started?

Getting Started Using Woodworking Projects and Strategies for Beginners

Before starting anything, it’s essential to choose the woodworking projects that you want to start with. As a beginner, always pick a project that has quite a basic build up or a very simple structure. A few easy to begin projects include, bird feeder, chairs, shelves, etc.. As soon as you find the techniques, you can always move into the next level of woodworking projects, like cupboards, sheds, and others. Beginning projects should always keyword be complicated and less bothersome so that you have a better knowledge of working with forests and their resources. When the job is selected, start selecting your tools.

Beginners Woodworking Tools, Garage Shed Plans

Tools are the ways through which you will win the battle of woodworking. A lot of people believe power tools are requires. But for beginners, basic hand tools can be quite handy and more than helpful in completing a project. If woodworking is your hobby, then some tools that you would require are:

1. Workbench – A workbench is needed for precise cuts and dimensions. Even the workbench, when fixed with vises, offer ample space to work. As a key tool, workbench must be part of your newcomer’s woodworking tools.

2. Hammer – Hammer is also a vital tool for woodworks. It can help you to drive pins, nails, staples, etc.. A small and lightweight hammer can make things considerably simple for you. When you purchase a hammer, constantly assess the equilibrium between the weight and endure. Always pick a sturdy, yet lightweight product.

3. Saw – A saw is just another tool which you cannot live without while woodworking. |} This tool can help you to cut woods at several sizes. There are various sorts of saws out there in the marketplace. Decide on a size that you could deal with.

4. Screwdriver – Screwdrivers are available in various shapes and sizes. Mostly you will find Canadian kinds and standard flat kind. Having all of them can help you in advance woodworking. You might also buy keyword energy screwdrivers since they make the job much quicker.

5. Measuring tape – It is another essential tool that you cannot work without. The measuring tape helps you to quantify wood until they may be attached together.

6. Wrench – Some woodworking jobs require fixing bolts and fixes. For such projects, you require a wrench. Nonetheless, this is not a tool for beginners, but using it would make work easier for you in a subsequent stage.

7. Drill – Drill makes it possible to create holes in timber. Low wattage power drills will make the task much easy.

8. Additional small and fundamental tools – These include pencils, gum, basic gum, level, erase, first aid kit and shop vac.

Costing and Budget for Your Project

There’s not any fixed cost on woodworking projects. Dependent on the type of project you want to finish, pricing can be determined. The simple the project, the less price it involves. But at the very beginning purchasing the tools will probably be somewhat hefty. Therefore, it is better to fix a budget on the tools, then keyword on the undertaking. Purchasing the basic tools will ensure that you do not need to purchase any more material other than the wood ply.

Time and Directions

Directions are among the principal things which every beginner should follow. Instructions guide is quite easy to comprehend the procedure, what to do and how to do it. Time also plays a significant part in the construction of woodworking projects. Woodworking projects demand time and therefore it is necessary for a novice to have ample quantity of time weekly.

Ideas for Beginners

There are no quick tips or suggestions that will make the work easy. Nevertheless, the most indispensable thing keyword that can allow you to reach success is proper planning. With proper planning and a strategy, it’s likely to achieve success immediately. If you know the objective of woodworking, the thing you want to construct, the tools you need in order to possess and the average time you can give daily; then you’re all set to go.

Conclusion, Garage Shed Plans

These tips and instruction will make the woodworking projects and strategies for novices quickly to finish. Always make sure that you have all the essential tools, materials, space ready. Read the instructions for constructing a product handy. Proper strategy and preparation can allow you to make a fantastic woodworking project for your home.

|

Starting Your First Woodworking Shop Garage Shed Plans

People when looking for a way to pass time or want an alternative method to make money they usually turn to a hobby they enjoy. It’s very exciting to do and everyone can get started.

When doing woodworking in your home there are lots of jobs one can think of. When starting out you need to be very cautious when choosing which project to begin with since you will find projects that may be too tough for a newbie. But do not worry about that since we are going to provide you tips on the ideal way to start woodworking as a beginner.

The same as any other hobby woodworking requires some working gear, so before you choose your job you need to be aware of if you’ve got the available resources to work on such a project. Try not to spend a lot of money on buying equipment when starting out, buy more gear as you gain more experience and become a professional carpenter. If you enjoy your hobby then there will not be any difference between the hand and the hands.

Woodwork Crafts – The Beginners Guide To Woodworking Garage Shed Plans

Woodworking in your home will give you time to research different projects and find out a lot of things. That’s why it’s important to spend less money when starting out so you can manage to make mistakes and at some time learning about various jobs.
It’s extremely important you know more about different types of wood available for making jobs. Expect carpenters use different kinds of wood quality for decorating pieces, learning which type of wood they use can allow you to prepare the wood you will need for certain projects you may choose to pursue.
As soon as you understand the basics of wood selection and the usage of different tools you can now implement them in cutting well wood pieces and placing wood together. Knowing what to do will assist you in building good projects to fulfill your needs.

Garage Shed Plans practice makes perfect so make sure that you practice your work every day if possible. Try out a lot of layouts using a variety of tools so you can get the hang of using the tools. When starting out you may earn a number of mistakes but with time you will find out how to properly utilize them and create quality projects.

|

How to Become a Master Woodworker From Your Own Home Garage Shed Plans

Woodworking as a hobby may be among the most rewarding experiences you will ever appreciate. You can get started on a shoestring with a minimum amount of gear and equipment. A small home workshop may generate a broad array of simple projects that will allow you to develop your creative and construction skills while rewarding you with artistic and practical wood products that you are able to appreciate and even give away to friends and family.

WHERE TO DO YOUR WOODWORKING

Before we get into the equipment you ought to begin with, let’s discuss where you will do your woodworking, based on the size of your home, you may have the ability to produce a dedicated space into your woodworking tasks. This may be a reserved spot on your garage or on your basement. In some cases, a detached shed or outbuilding may be perfect to set up your very first store. A heated store detached from your home offers one distinct advantage: better dust control. Without sophisticated dust control systems, basement assignments will inevitably produce dust which travels into the living area of your house. This is very true in homes with forced air heating systems in which cold air yields located in the basement draw up dust into the top levels of the home. Another advantage of detached workshops is, clearly, the noise level. You can work without bothering the remainder of the family. A fantastic compromise might be the garage of your property.

This might help decrease the difficulties of dust and sound, however based on where you reside, a keyword garage layout may not be practical during extremes of cold or hot weather.

Finding Woodworking Projects and Plans for Beginners Garage Shed Plans

YOUR WOODWORKING SETUP

Space is always a struggle for the woodworker. Irrespective of where you are in your development, everyone from beginner to expert all wishes that they add more space to function in. Garage Shed Plans if you’re able to have a dedicated place for a workshop all the better. Floor tools and bench top gear can stay in place from project to project. If this installation isn’t hopeless, at least try to create a bench area where equipment can be stored and pulled out as necessary. If possible plan for inevitable growth as you get more tools and gear. At the beginning, establish a bench area where you can shop and use the majority of your gear, using a temporary expansion of your activities onto the basement or garage floor.

A basic workbench can be constructed from cheap spruce lumber ideally at least 48 to 54 inches wide and 32 inches deep. |} The bench should be around waist height. That will enable you to work comfortably while standing. Insert a sturdy shelf below the seat to house your hands power tools along with a pegboard above the bench to hang other equipment. Put in a woodworking vice at one end of the seat on the front to hold small workpieces.

ACQUIRING YOUR EQUIPMENT, Garage Shed Plans

The scope of your startup equipment will be largely based on your budget. Whether you’ve got large financial resources or you are starting on a shoestring always purchase quality equipment. If you can afford it, then purchase your quality tools in the local building and hardware centre. If your budget is tight purchase quality used tools from others through Kijiji or other regional ads. You will find plenty of quality lightly used programs out there which belong to people who embarked on that 1 molding project around the home or received tools as presents that they won’t ever utilize. You can usually purchase tools for all these sellers for under half of the original cost and save even more money if you create a package deal for all their unused equipment. Obviously, getting tools from private people will require extra time and possibly travel expenses. Weigh out the advantages of traveling around town to save a few added bucks on a inexpensive piece of equipment. The excess expense of travel and time in these situations is usually justified when buying large ticket items like table saws, bandsaws or large finished tools like surface planers in the future.
For smaller acquisitions, a trip to your building center could possibly be the ideal approach.

START-UP EQUIPMENT

In earlier times skilled employees worked with a minimum quantity of hand gear yet produced sophisticated and intricate pieces. Focus on developing your abilities with your start-up set of resources and prevent lamenting about the equipment you wished you’d.
Here’s a listing of the useful tools You Will Need to get started:
Safety Equipment: Start as expected with eye protection. Get a nice pair of safety glasses which also offer some side protection to your eyes. Buy a quality oil set that will be scratch resistant. Progressive scratching of thinner plastic pairs will eventually impair your vision and influence safety. Avoid wearing goggles in a workshop. Most impair eyesight and dust up fast. You can avoid wearing them all together if you find them uneasy.

The next piece of critical safety equipment you’ll need involves ear protection. Ear protection can be overlooked by the novice woodworker yet is almost as critical as eye protection. Woodworking may be noisy and long-term exposure to those sound levels may affect hearing and result in tinnitus and other hearing losses. Also, I find that wearing hearing protection combats fatigue.

Most employees tire quicker when exposed to elevated noise levels. Last, put on a cap to keep the dust from your hair. I prefer a simple ball cap along with my ear muffs and eye protection. With this set up I am protecting my eyes and my ears. I’m keeping the dust out of my hair. I’m good to go!

Power Hand Saw: Frequently known as a skill saw after the favorite name, this may prove to be the most versatile instrument in a startup workshop. In fact, at the hands of an expert, a power hand saw can be used to construct an entire property. At some point, you’ll want to buy a table saw, but for the time being, a power hand saw for the woodworker on a budget enables him to perform cross cuts, rip cuts and even intricate angle cuts. As mentioned before get an excellent manufacturer saw. Stay away from cheap unknown brands. These tend to cut back and will burn out before you start your next project. After choosing the right saw install a quality blade. Most skill saws come with a starter blade of lesser quality even if they are a good saw. Keep this blade as a copy and put in a quality blade with carbide teeth. Begin with a hybrid .

Power Jig Saw: A jigsaw will include great versatility to a woodworking. |} Curved cutting is the point where the jigsaw excels. This flexible tool can’t only cut corners. It is ideal for cutting holes in wood too like manage slots. At some point, you’ll want to get a ring saw. Bandsaws are much more versatile but a excellent floor unit can be expensive. A jigsaw may be a fantastic stop gap to the novice woodworker.

Purchase an range of blades for your own jigsaw that includes various lengths and teeth per inch.

Battery Powered Drill: buy an excellent drill that runs on at least 12 volts, however, 18 volts is better. |} Get one with a keyless chuck and if it is in your budget contemplate a 1/2 inch toss over the standard 3/8 inch model. Through tough lessons learned, I have found that purchasing quality, in this scenario, is much more critical than ever. Cheaper drills tend to have very short run times and need to be recharged often. Their long-term battery life tends to be bad and to make matters worse keyless chucks come loose and slide frequently. This is 1 annoyance you don’t need on your workshop. Purchase an assortment of quality carbide tipped drill bits which are kept in a holder tagging each drill bit size. Create a habit of returning each drill bit to its prospective slot at the holder after every use. Lastly, get a set of tough steel driver bits. Your drill can also be a flexible screwdriver, especially if you picked an 18-volt version.

Hammer: The hammer remains as the most flexible tool in the store, and often the most misunderstood one. |} Incidentally, the hammer is the one instrument where most workshop accidents occur. Even though the most ordinary, hammer accidents are often of a minor character, varying from bruised palms into the temporary loss of a fingernail. Hammers greatly vary in quality and price. So what’s the difference between a inexpensive hammer and an expensive hammer? Quality hammers are just machined with a good solid joint between the handle and mind. The fantastic hammer is balanced, does not rust and features a comfortable grip. Most hammers in the high tech range provide ceramic or metal handles. Cheaper hammers generally have wood handles with inferior joints between the handle and head. The mind usually comes loose and the instrument becomes useless. Select a title brand quality hammer at the 16-ounce scope for general work and also a smaller finishing hammer for more complex work. Avoid using large framing hammers at the workshop and some other with dimpled head tips. These types of hammers are more appropriate to rough framing tasks and therefore are unsuitable from the workshop.

Palm Sander: Buy a 1/4 sheet . This tiny power tool can handle just about any trimming requirements that you’ve got as a novice woodworker. As your woodworking skills evolve, you will probably upgrade to a floor model disk and belt sander. But for now, the ever-versatile palm sander can clean up edges, cross cuts and perhaps even limited quantities of surface space. As you embark on the first few projects you might discover your palm sander with just a bit of effort can change rough looking creations into virtual functions of art! It is possible to use your palm sander to sand and shape rough boards using 100 grit paper and later finish your job with 200 or even 300 grit paper. Purchase an range of sandpaper sheets using an extra supply of 100 grit paper. You’ll get that this caliber of paper that the most versatile in your store.

Hand Planes and Chisels: These classic tools are a must in each workshop. |} Though low tech in theory, these tools allow you to taper edges, flatten high spots and correct any imperfections in timber pieces. {Start with a typical number 4 airplane and an range of quality chisels varying in diameter from 1/4 inch to 1 inch.

Clamps: Sooner or later you will need clamps for glue-ups and just to hold down your wood pieces as you operate on them. Unfortunately, superior clamps are costly and it normally requires the novice woodworker a couple of years to collect a comprehensive set of timber clamps. Begin with a set of extended”pipe” clamps. Now the pipe was replaced with long steel shafts, but the structure remains the same. Get a pair of the maximum clamps that you can spend. You can get in touch with them for smaller glue jobs and enlarge them to their entire length for larger jobs.

Shop Vice: A store vice installed at the end of your seat is perfect for holding smaller jobs for sanding, filing, and gap cutting with your jigsaw. Purchase a woodworking with stainless steel clamping surfaces and prevent metal functioning vices with steel jaws. Woodworking vices using their timber clamping surfaces can securely hold wood pieces without marring or damaging them. A number of the better vices offer you rapid release mechanisms that enabled the consumer to rapidly open and close the limbs without dull handle turning. The wood beamed surfaces in your vice will occasionally need replacement. I would rather utilize soft walnut in my vices which will not crush or damage lots of the various forests that I utilize. Whether I am working in walnut or hard walnut, softwood clamping surfaces function the best.

Tape Measure and Marking Device: On your workshop, the ever-humble tape step will be one of the most often used tools. Buy a good quality name brand tape measure with a broad tape usually from the 25-foot selection. Even though in your shop you may not use the tape at these spans, the bigger tape measures provide more rigid tapes that will not flop around and slip off the end of boards. Measuring when you are on your own will be a lot easier, and of course, quality tape steps can endure for several decades.

When marking jobs, I favor a sharp great old-fashioned HB pencil. An HB pen will produce a wonderful mark without scratching the timber. Avoid oversize carpenter’s pencils. Their big flat leads are just too rough for accurate measurement in the workshop.

Additional Tool and Materials: Here are a few other useful tools to round out your starter workshop: Purchase a T-square, set square and rate square. These inexpensive tools can assist you in marking the right angles as well as chemical angles. Get the number two and three Robertson set. I find that the Robertson format works great for many woodworking projects and will be the most compatible with a drill powered bits. Lastly, get a set of 12-inch wood files. The cost of adhesive through all your jobs is a little cost consideration. Therefore, it is sensible to decide on the best. I have also discovered over time that I receive the best results with both indoor and outdoor jobs when I use quality outside grade adhesive. All these resin-based compounds unlike conventional water-based wood adhesive, will not break down and fail with moisture.

CONCLUSION, Garage Shed Plans

The peaceful gratification of woodworking is a wonderful adventure in this day and age of rushed lives, smartphones, and time-starved livelihood. With a minimal investment in the most basic tools and equipment, everyone can learn the profitable skills of his time-tested hobby and enjoy project after project!

  • California Closets adds Baltimore and New Jersey locations to company-owned operations

    TORONTO - FirstService Corporation, the parent company of California Closets, expanded its company-owned operations with the acquisitions of Baltimore and South New Jersey franchises. 
     
    “These two acquisitions provide key market footholds in the attractive and growing Mid-Atlantic region,” said Charlie Chase, President & CEO of FirstService Brands. “Both operations will benefit from the migration of production into our eastern centralized manufacturing facility in Grand Rapids, Michigan and ongoing investments to increase capacity,” he added.
     
    Following both transactions, California Closets now has 19 company-owned operations among its 80 total franchised territories. Terms of the transactions were not disclosed.
     
    For more information, visit firstservice.com.
     

  • Recession coming? Find out from EBC keynote Alan Beaulieu

    San Jose -- Alan Beaulieu, president and a principal of ITR Economics, will discuss the economic outlook for 2019 in a webinar on Tuesday, January 29 at 3 p.m. Eastern.  His presentation, "Shifting Gears and Looking Ahead," will discuss how the U.S. and global economies are not what they were last year and what to expect in 2019.  The changes that he will discuss include:

    • Policy pressures/benefits on business
    • Consumer behavior
    • Business spending
    • Labor market
    • Commodity prices
    • Interest Rates
    • Impact on our markets

    Attendees will be prepared for the rest of 2019 and will have the confidence to effect tactical changes that will enhance profitability through 2020.  Since 1990, Beaulieu has consulted across North America, Europe, and Asia, optimizing companies’ forecasts and planning to increase profits through his mastery of business-cycle trend analysis. Alan also serves as Senior Economic Advisor to numerous U.S. and international trade associations.  The webinar will be moderated by FDMC editor, Will Sampson.  Register for the webinar.

    Beaulieu has been a frequent keynote at the Executive Briefing Conference, which will be held April 14-16 at the San Jose Marriott. View the full agenda.   The 2019 EBC provides strategic and practical information that addresses manufacturing challenges, and a forum for discovery. EBC helps executives anticipate business opportunities and beat the challenges that lie ahead and will ignite and inspire business leaders to create change when they return home.

  • 2020 holiday design contest winners announced

    LAVAL, Canada - 2020 recently announced the winners of its 2018 Holiday Design Fest Contest. Interior designers submitted their "jolliest and cheeriest" designs using 2020 Design and 2020 Fusion. 
     
    “All the designs that were submitted are both beautiful and very festive,” says Santiago Morales, 2020 Design product manager. “I’m glad designers are using the new 2020 Cloud Decorative Items to decorate their designs, and we will continue to add new items to give users a chance to be even more creative with their designs.”
     
    2020 recently added an array of festive items to its 2020 Cloud that designers can use to create holiday-themed designs. The 2020 Decorative Items catalog is compatible with recent versions of 2020 Design and 2020 Fusion.
     
    The winners of the 2020 Holiday Design Fest Contest are:
    2020 Design: Jessica McLeland from Cabinets.com
    2020 Design: Amy Anderson from Cabinets.com
    2020 Fusion: Paul Abdy from Building & Plumbing Supplies LTD
     
    To learn more about the 2020 holiday design gest contest winners, please visit the 2020spaces.com/2020products/2020-holiday-design-fest/contest/2018-gallery.
     

  • Sustainability challenges to be discussed at Decorative Surfaces Conference

    MIAMI -- All economic activities that occur in the natural world require resources such as energy, materials and land, while generating waste and polluting emissions as unwanted byproduct. Today the demand for natural resources and the production of pollution exceed the regenerative capacity of the Earth and put us face to face with one of the biggest challenges of our time: moving towards a sustainable economy. But what does sustainability mean? Despite its simplicity, sustainability is a concept people have a hard time wrapping their minds around: Is it all about recycling? Are “green” or “natural” synonyms for “sustainable”? And last but not least: how can sustainability be addressed in the laminates industry? Does durability play a role there? Let's dig into those questions and debunk some myths.  Dr. Alessandra Fusi, Sustainability specialist with Trespa and Arpa will address all of these questons in her presentation, "Facing the Sustainability Challenge: What Cards Can Our Industry Play?"
     

    The Decorative Surfaces Conference is produced by TCM North America.
    See the FULL PROGRAM HERE.

    REGISTER

    The meeting will be held at the beautiful Miami Biltmore Hotel for two days of presentations from the global leaders in design and surfacing technology. Ample time for networking, and even a little golf, make this the industry’s top event for users of decorative surfaces. Don’t miss it!

    Contact Kenn Busch – [email protected] – with questions about attending and sponsoring.

     

  • WMS 2019 reports brisk exhibit sale activity

    Mississauga – CCI Canada, the organization that runs the 2019 Woodworking Machinery & Supply Conference and Expo, reports that exhibit sales are running well ahead of last year’s event a year out from the show.  WMS, to be held October 31 to November 2, 2019,  is more than 30% ahead of the 2017 event's pace in terms of exhibitors and exhibit space.  “Our 2017 event created a lot of positive momentum and exhibit space sales have continued on a roll since then,” said Tim Fixmer, CEO of CCI Canada, Inc.  WMS 2017 featured more than 270 companies and brands.  “We’ve seen a great uptick in new exhibitors and also exhibitors returning after missing a few show cycles,” said Fixmer.
    Planning is underway for an expanded conference agenda that includes an opening morning keynote that will be free for all attendees.  “We plan to have a marquee presenter to kick the show off in a big way,” said Harry Urban, WMS show manager.
    The education portion of WMS will feature two learning tracks and keynote luncheons.   “Our education program will be devoted to best business practices and technology and design trends,” said Urban.   Also new this year will be learning on the show floor.
    According to Urban, a post event survey from WMS 2017, revealed 87% of the show’s 4,500 attendees plan to return to next year’s show.  "This is the show that brings our industry together and makes it stronger," said Trevor Chaulk, president of Chaulk Woodworking in Minden, ON. "With a vast array of topics in the seminars,supplier networking and machinery advancements it provides the tools for a great future in the wood industry," he said

    Registration for WMS 2019 will open in Spring.  Go to wmscanada.ca for updates.

    About CCI Media
    CCI Canada is owned by CCI Media, a business-to-business media company focused exclusively on industrial wood products manufacturing markets in North America. CCI Media’s flagship publication, FDMC magazine, circulates monthly in print and digital formats. CCI Media also publishes the bi-monthly Closets & Organized Storage Magazine. Woodworking Network is the umbrella brand for the combined portfolio of wood manufacturing print, digital, and web products and industry events operated by CCI Media.   
     
    In addition to WMS 2019, CCI Media produces Wood Pro Expo Charlotte and the Cabinets & Closets Conference & Expo, both of which will be co-located March 6-8, 2019 at the Charlotte Convention Center.  
    The company also produces Wood Pro Expo Lancaster 2019, to be held October 17-18, at Warehouse at the Nook, Manheim, PA and the Executive Briefing Conference, April 14-16 in San Jose, CA.
     

  • Next month's Decorative Surfaces Conference offers a glimpse of the future

    MIAMI -- Get a glimpse of the future at the Decorative Surfaces Conference 2018, 4-6 December in Miami, organized by TCM North America.

    Conference topics include:

    •    The latest on lightweight decorative surfaces: Not just for RTA anymore! The incredible realism of these materials have put architectural surfaces in play. We’ll be analyzing these opportunities.

    •    3D Laminates :  The new design leader? Flexible surfaces offer design options no other material can, and specifiers are taking notice.

    •    Digital scanning and printing of decorative surfaces come of age: Technology that scans and print not just visuals, but textures as well, is about to revolutionize the surfacing industry.

    •    Are composite-wood decorative panels the most sustainable option on the planet? New ways of defining “sustainability” put our materials solidly at the top of the green column.

    •    Formaldehyde:   Addressing “The F-word” with a dose of common sense. There’s a broader context in which we should be talking about this basic organic building block used in thousands of everyday products.

    VIEW FULL PROGRAM.

    The  meeting will be held at the beautiful Miami Biltmore Hotel for two days of presentations from the global leaders in design and surfacing technology. Ample time for networking, and even a little golf, make this the industry’s top event for users of decorative surfaces. Don’t miss it!

    REGISTER before November 9 and save $100.

    Preferred hotel rates end in 9 November, or until our reserved block of rooms is gone, so don’t delay!

    Contact Kenn Busch – [email protected] – with questions about attending and sponsoring.
     

  • Closets industry study findings to be revealed in Charlotte

    CHARLOTTE -- The results of a state of the industry study conducted by Closets & Organized Storage Magazine will be presented exclusively to attendees of the Cabinets & Closets Conference & Expo, March 6-8 at the Charlotte Convention Center.  "We're excited to conduct this study to see where the industry stands and where it's headed, " said Laurel Didier, publisher of Closets & Organized Storage. CCCE 2019 attendees will be the first to receive the results by participating in our conference on March 6." View full conference agenda.

    The main focal points of the study include:

    • The size of the industry.
    • The average sales price for a  master bedroom walk-in closet, laundry room, mudroom, multi-use room with a wall bed and built-ins and garage cabinets and storage
    • The most commonly requested accessories for a master bedroom closet and garage makeover.
    • The average sales volume for closet companies, independent vs dealers, franchisees.
    • Colors and materials are trending in closet and garage cabinets
    • How are designers compensated?
    • Designers average closing ratio.
    • What percentage of  closets companies ' products do they make vs buy?
    • What is the craziest thing a customer asked a designer to include in the design plans?
    • What keeps closet industry executives up at night?

    The Cabinets & Closets Conference & Expo is an annual event featuring a full-day conference, plant tour, and exposition, and is dedicated to home remodeling professionals specializing in building kitchen cabinets, closets, and other home storage designs. Scheduled for March 6-8, 2019 at the Charlotte Convention Center, the Cabinets & Closets Conference and Expo will co-locate with Wood Pro Expo, which is held annually in Charlotte.
    The Wood Pro Expo brand comprises a series of strategic regional events, located in key areas throughout the United States where professional woodworkers congregate. Wood Pro Expo features a full day of education and tours followed by two expo days oriented to equipment and supplies focused on the small-to-medium size shops. The educational offering includes CNC basics, employee recruitment, finishing, lean manufacturing, business management, software, and shop safety. For information on Wood Pro Expo Charlotte, visit WoodProExpoCharlotte.com.

     

  • Learn about American Woodmark's foray into RFID

    ATLANTA, GA -- According to Henry Nisiobincki, the idea that each item is unique in woodworking holds true more than in any other industry. Nisiobincki, RFID Program Manager at American Woodwork Corporation, faced this challenge as he guided the company to benefit from RFID (Radio-Frequency Identification) technology.

    "The questions we asked were, how could we identify the unique history of each unique part?  And how can we use that information to help measure quality, control process flows, and improve inventory accuracy?"

    Nisiobincki said that by using integrated RFID technology to create a unique identity for each piece, American Woodmark Corporation has seen continuous benefit and value.  He will show how a simple low-cost addition to each piece can be the solution for endless cost-savings, as well as the platform for future innovation.  He will discuss American Woodmark's RFID integration  in his presentation at IWF on August 21, titled,  A Unique Technology, in a Unique Part, for a Unique Industry. His session is part of the all-day Woodworking Network Leadership Forum.  The Leadership Forum is sponsored by J B Cutting.

    At American Woodmark Corporation, Nisiobincki manages the RFID Program from a corporate level. He works closely with  the organization's manufacturing plants to understand processes, identify key issues, and develop unique and innovative RFID technology solutions to relieve those issues. His career at American Woodmark started in IT Development and IT Project Management before transitioning into RFID. He said  is excited to share the unique and extensive application of RFID at IWF.


    The targeted audience for this session includes: C-Level management, rising stars and innovators from across the wood products industry including CEO’s, owners, team managers and entrepreneurs and investors.  Registration for the Woodworking Network Leadership Forum is $395 until August 1 and $450 thereafter.  Lunch and admission to the Leadership Reception following the symposia are included.

     

  • Bespoke founder, Keith Morgan, kicks off Leadership Forum at IWF

    ATLANTA, GA -- Keith Morgan knows a thing or two about design.   He also has a knack for employing, training and retaining a talented staff.   His company, Bespoke, caters to an elite international clientele base, emphasizing elegant custom design and spectacular craftsmanship. Not only has Bespoke won multiple Craftsman’s Challenge awards, but also Morgan has earned a reputation for his marketing prowess in the highly competitive world of catering to luxury consumers.   Morgan will be the keynote presenter to kick off the Woodworking Network Leadership Forum on August 21 (the day before IWF opens) at the Georgia World Congress Center. 

    In his keynote titled, Leadership by design, Morgan will discuss the importance of professional design in all aspects of your business including design, manufacturing, and marketing.   According to Morgan, it is essential to integrate a solid design professional or professionals within your front office operations. The organization must have individuals who have experience in the interior design industry but also be able to take on and understand construction techniques at the shop floor level.

    Bespoke has one multiple Craftsman's Challenge Awards.

    His presentation at the 2018 Cabinets & Closets Conference & Expo in Pasadena, Selling directly to the luxury consumer, received outstanding feedback from the audience.  Morgan stresses that it is critical to employ professionals that understand market-viable design and long-term design trend history.   Morgan will also discuss the importance of hiring talented craftspeople and what Bespoke does to retain them indefinitely. 

    He will also address how Bespoke has successfully linked itself to other luxury brands and how you can link your product with other luxury brands to “ride on the coattails of their recognized luxury brand status."
     
    Woodworking Network Leadership Forum at a glance
    Target Audience: C-Level management, rising stars and innovators from across the wood products industry including CEO’s, owners, team managers and entrepreneurs and investors
    Sponsor:  JB Cutting, Inc.
     
     
    9:00 AM  – 10:00 AM - Keynote -- Leadership by Design (presented by Keith Morgan)
     
    10:00 AM - 11:00 AM - Building Bigger, Taller and Stronger with Wood: How Mass Timber is Rolling out in the U.S.
    Products such as cross laminated timber, popular in Europe for more than 20 years, are now making their way into North America in a serious way, with manufacturers in Oregon, Washington, Montana and Alabama coming onstream and innovative new timber buildings appearing in many of our cities. In this presentation, Iain Macdonald, Associate Director of the TallWood Design Institute, will describe mass timber and how it is changing the way America builds. He will cover manufacturing, technical barriers and how they are being overcome, expectations for market growth, and what it means for providers of non-structural wood products.
     
    11:00 AM - Noon - A Unique Technology, in a Unique Part, for a Unique Industry
    Each item is unique, and in woodworking, this is even truer than any other industry. But how could we identify the unique history of each unique part? And how can we use that information to help measure quality, control process flows, and improve inventory accuracy? Using integrated RFID technology to create a unique identity for each piece, American Woodmark Corporation has seen continuous benefit and value.  Henry Nisiobincki will show how a simple low-cost addition to each piece can be the solution for endless cost-savings, as well as the platform for future innovation.
     
    Noon - 1:00 PM - Networking Lunch
     
    1:00 PM - 2:00 PM - Nanotechnology: Small to the World, Big to the Industry
    There's an unprecedented multidisciplinary convergence of scientists dedicated to the study of a world so small, we can't see it - even with a light microscope. Mike Hetherman, president, owner and CEO of Willis - a North American distributor of globally branded building materials and a prominent voice in the design community, will address the field of nanotechnology, the realm of atoms and nanostructures. Nanotechnology is so new, no one is really sure what will come of it. What we do know is that nanotechnology is making its way into the world of building materials. Join us for an intriguing session which will outline the basics of nanotechnology and how it’s being used to revolutionize our industry.
     
    2:00 PM - 3:00 PM - The Business Case for Diversity
    Diversity is quite possibly the best source of innovation and creativity in our industry, according to Whitney Pyle who is also a Woodworking Network Class of 2017 40 under 40 winner. Whitney will discuss her career path through the industry as a female. "The construction and woodworking industries as a whole lack diversity," said Pyle.She said many times when she attended industry events people would presume she was just somebody's spouse. "Together, we will unpack the reasons why, we’ll discuss why it’s important to change it, what we can do to change it," said Pyle. "We’ll also discuss what steps to take to ensure all people become integrated and engaged in our organizations and our industry."
     
    3:00 PM - 4:00 PM - Understand the New Consumer
    This presentation lead by Mike Hetherman, will unearth two very distinct types of consumers – the NEO and the Traditional – and how they are powering our economy.  Discover why targeting one versus the other will drastically change your sales, marketing and pricing strategies forever. You’ll learn who spends the most, most frequently, and find out more about their values, attitudes and, ultimately, buying behavior and communication preference.  Most importantly, you’ll learn how to quickly connect with your customer, close jobs faster, work less and maximize your profits.
     
    4:00 PM - 5:00 PM - 40 under 40 leadership panel:
    Woodworking Network’s 40 under 40 award recognizes those individuals that have made a difference in their careers, their companies, their communities and to the industry.  Benchmarks include productivity, profitability, social good, innovation, peer inspiration, product development and organizational leadership. 
     
    This illustrious panel, made up of members of the Class of 2018 and alumni, will address their leadership journey and offer insights into the future of the industry.
     
    The Leadership Forum is followed at 5:30 PM by a Leadership reception to recognize the 40 under 40 Class of 2018. 
     
    All registrants for the Leadership Forum are invited to attend. Registration to attend IWF is included in the cost of admission.  Click HERE to register for the Leadership Forum
     

     

  • Contrat historique pour Conception R.P.

    Conception R.P. commence la conception puis la fabrication d’un projet d’envergure aux États-Unis pour un fabriquant de bois lamellé-croisé ou sous l’acronyme CLT (Cross Laminated Timber). Le projet se réalisera sur une période d’un peu plus d’un an et créera près de 10 à 15 emplois à temps plein dans la ville de Québec.
     
    « Nous sommes fiers de travailler avec un tel joueur dans l’industrie. L’aboutage de bois leur permettra d’utiliser des planches de bois plus courtes pour leur besoin et ainsi leur donner une plus grande flexibilité sur le plan des achats et de la production » Louis-André Levesque, Responsable du développement des affaires chez Conception R.P.
     
    L’usine comprendra un système de dépilage des bois, un système de vision pour analyser les défauts, des scies automatiques à haute vitesse pour couper les défauts, le système d’aboutage à haute vitesse CRP-3000, un grand convoyeur de séchage des bois, des ébouteuses de précisions, un empileur de paquets automatique puis un système de sanglage des paquets.
     

Shed

A shed is typically a simple, single-story roofed structure in a back garden or on an allotment that is used for storage, hobbies, or as a workshop. Sheds vary considerably in the complexity of their construction and their size, from small open-sided tin-roofed structures to large wood-framed sheds with shingled roofs, windows, and electrical outlets. Sheds used on farms or in industry can be large structures. The main types of shed construction are metal sheathing over a metal frame, plastic sheathing and frame, all-wood construction (the roof may be asphalt shingled or sheathed in tin), and vinyl-sided sheds built over a wooden frame.

A culture of shed enthusiasts exists in several countries for people who enjoy building sheds and spending time in them for relaxation. In Australia and New Zealand there are magazines called The Shed, an association for shed hobbyists (the Australian Men's Shed Association), and a book entitled Men and Sheds.

The simplest and least-expensive sheds are available in kit form. These kits are designed for regular people to be able to assemble themselves using commonly available tools (e.g., screwdriver). Both shed kits and DIY (do-it-yourself) plans are available for wooden and plastic sheds. Sheds are used to store home and garden tools and equipment such as lawn tractors, and gardening supplies. In addition, sheds can be used to store items that are not suitable for indoor storage, such as petrol (gasoline), pesticides, or herbicides. For homes with small gardens or modest storage needs, there are several types of very small sheds. The sheds not only use less ground area but also have a low profile less likely to obstruct the view or clash with the landscaping.

Video: Woodworking Tools